/**************************************************************************/ /*! @file Adafruit_INA219.cpp @author K.Townsend (Adafruit Industries) @license BSD (see license.txt) Driver for the INA219 current sensor This is a library for the Adafruit INA219 breakout ----> https://www.adafruit.com/products/??? Adafruit invests time and resources providing this open source code, please support Adafruit and open-source hardware by purchasing products from Adafruit! @section HISTORY v1.0 - First release */ /**************************************************************************/ #if ARDUINO >= 100 #include "Arduino.h" #else #include "WProgram.h" #endif #include #include "Adafruit_INA219.h" /**************************************************************************/ /*! @brief Sends a single command byte over I2C */ /**************************************************************************/ void Adafruit_INA219::wireWriteRegister (uint8_t reg, uint16_t value) { Wire.beginTransmission(ina219_i2caddr); #if ARDUINO >= 100 Wire.write(reg); // Register Wire.write((value >> 8) & 0xFF); // Upper 8-bits Wire.write(value & 0xFF); // Lower 8-bits #else Wire.send(reg); // Register Wire.send(value >> 8); // Upper 8-bits Wire.send(value & 0xFF); // Lower 8-bits #endif Wire.endTransmission(); } /**************************************************************************/ /*! @brief Reads a 16 bit values over I2C */ /**************************************************************************/ void Adafruit_INA219::wireReadRegister(uint8_t reg, uint16_t *value) { Wire.beginTransmission(ina219_i2caddr); #if ARDUINO >= 100 Wire.write(reg); // Register #else Wire.send(reg); // Register #endif Wire.endTransmission(); delay(1); // Max 12-bit conversion time is 586us per sample Wire.requestFrom(ina219_i2caddr, (uint8_t)2); #if ARDUINO >= 100 // Shift values to create properly formed integer *value = ((Wire.read() << 8) | Wire.read()); #else // Shift values to create properly formed integer *value = ((Wire.receive() << 8) | Wire.receive()); #endif } /**************************************************************************/ /*! @brief Configures to INA219 to be able to measure up to 32V and 2A of current. Each unit of current corresponds to 100uA, and each unit of power corresponds to 2mW. Counter overflow occurs at 3.2A. @note These calculations assume a 0.1 ohm resistor is present */ /**************************************************************************/ void Adafruit_INA219::setCalibration_32V_2A(void) { // By default we use a pretty huge range for the input voltage, // which probably isn't the most appropriate choice for system // that don't use a lot of power. But all of the calculations // are shown below if you want to change the settings. You will // also need to change any relevant register settings, such as // setting the VBUS_MAX to 16V instead of 32V, etc. // VBUS_MAX = 32V (Assumes 32V, can also be set to 16V) // VSHUNT_MAX = 0.32 (Assumes Gain 8, 320mV, can also be 0.16, 0.08, 0.04) // RSHUNT = 0.1 (Resistor value in ohms) // 1. Determine max possible current // MaxPossible_I = VSHUNT_MAX / RSHUNT // MaxPossible_I = 3.2A // 2. Determine max expected current // MaxExpected_I = 2.0A // 3. Calculate possible range of LSBs (Min = 15-bit, Max = 12-bit) // MinimumLSB = MaxExpected_I/32767 // MinimumLSB = 0.000061 (61uA per bit) // MaximumLSB = MaxExpected_I/4096 // MaximumLSB = 0,000488 (488uA per bit) // 4. Choose an LSB between the min and max values // (Preferrably a roundish number close to MinLSB) // CurrentLSB = 0.0001 (100uA per bit) // 5. Compute the calibration register // Cal = trunc (0.04096 / (Current_LSB * RSHUNT)) // Cal = 4096 (0x1000) ina219_calValue = 4096; // 6. Calculate the power LSB // PowerLSB = 20 * CurrentLSB // PowerLSB = 0.002 (2mW per bit) // 7. Compute the maximum current and shunt voltage values before overflow // // Max_Current = Current_LSB * 32767 // Max_Current = 3.2767A before overflow // // If Max_Current > Max_Possible_I then // Max_Current_Before_Overflow = MaxPossible_I // Else // Max_Current_Before_Overflow = Max_Current // End If // // Max_ShuntVoltage = Max_Current_Before_Overflow * RSHUNT // Max_ShuntVoltage = 0.32V // // If Max_ShuntVoltage >= VSHUNT_MAX // Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX // Else // Max_ShuntVoltage_Before_Overflow = Max_ShuntVoltage // End If // 8. Compute the Maximum Power // MaximumPower = Max_Current_Before_Overflow * VBUS_MAX // MaximumPower = 3.2 * 32V // MaximumPower = 102.4W // Set multipliers to convert raw current/power values ina219_currentDivider_mA = 10; // Current LSB = 100uA per bit (1000/100 = 10) ina219_powerDivider_mW = 2; // Power LSB = 1mW per bit (2/1) // Set Calibration register to 'Cal' calculated above wireWriteRegister(INA219_REG_CALIBRATION, ina219_calValue); // Set Config register to take into account the settings above uint16_t config = INA219_CONFIG_BVOLTAGERANGE_32V | INA219_CONFIG_GAIN_8_320MV | INA219_CONFIG_BADCRES_12BIT | INA219_CONFIG_SADCRES_12BIT_1S_532US | INA219_CONFIG_MODE_SANDBVOLT_CONTINUOUS; wireWriteRegister(INA219_REG_CONFIG, config); } /**************************************************************************/ /*! @brief Configures to INA219 to be able to measure up to 32V and 1A of current. Each unit of current corresponds to 40uA, and each unit of power corresponds to 800uW. Counter overflow occurs at 1.3A. @note These calculations assume a 0.1 ohm resistor is present */ /**************************************************************************/ void Adafruit_INA219::setCalibration_32V_1A(void) { // By default we use a pretty huge range for the input voltage, // which probably isn't the most appropriate choice for system // that don't use a lot of power. But all of the calculations // are shown below if you want to change the settings. You will // also need to change any relevant register settings, such as // setting the VBUS_MAX to 16V instead of 32V, etc. // VBUS_MAX = 32V (Assumes 32V, can also be set to 16V) // VSHUNT_MAX = 0.32 (Assumes Gain 8, 320mV, can also be 0.16, 0.08, 0.04) // RSHUNT = 0.1 (Resistor value in ohms) // 1. Determine max possible current // MaxPossible_I = VSHUNT_MAX / RSHUNT // MaxPossible_I = 3.2A // 2. Determine max expected current // MaxExpected_I = 1.0A // 3. Calculate possible range of LSBs (Min = 15-bit, Max = 12-bit) // MinimumLSB = MaxExpected_I/32767 // MinimumLSB = 0.0000305 (30.5uA per bit) // MaximumLSB = MaxExpected_I/4096 // MaximumLSB = 0.000244 (244uA per bit) // 4. Choose an LSB between the min and max values // (Preferrably a roundish number close to MinLSB) // CurrentLSB = 0.0000400 (40uA per bit) // 5. Compute the calibration register // Cal = trunc (0.04096 / (Current_LSB * RSHUNT)) // Cal = 10240 (0x2800) ina219_calValue = 10240; // 6. Calculate the power LSB // PowerLSB = 20 * CurrentLSB // PowerLSB = 0.0008 (800uW per bit) // 7. Compute the maximum current and shunt voltage values before overflow // // Max_Current = Current_LSB * 32767 // Max_Current = 1.31068A before overflow // // If Max_Current > Max_Possible_I then // Max_Current_Before_Overflow = MaxPossible_I // Else // Max_Current_Before_Overflow = Max_Current // End If // // ... In this case, we're good though since Max_Current is less than MaxPossible_I // // Max_ShuntVoltage = Max_Current_Before_Overflow * RSHUNT // Max_ShuntVoltage = 0.131068V // // If Max_ShuntVoltage >= VSHUNT_MAX // Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX // Else // Max_ShuntVoltage_Before_Overflow = Max_ShuntVoltage // End If // 8. Compute the Maximum Power // MaximumPower = Max_Current_Before_Overflow * VBUS_MAX // MaximumPower = 1.31068 * 32V // MaximumPower = 41.94176W // Set multipliers to convert raw current/power values ina219_currentDivider_mA = 25; // Current LSB = 40uA per bit (1000/40 = 25) ina219_powerDivider_mW = 1; // Power LSB = 800uW per bit // Set Calibration register to 'Cal' calculated above wireWriteRegister(INA219_REG_CALIBRATION, ina219_calValue); // Set Config register to take into account the settings above uint16_t config = INA219_CONFIG_BVOLTAGERANGE_32V | INA219_CONFIG_GAIN_8_320MV | INA219_CONFIG_BADCRES_12BIT | INA219_CONFIG_SADCRES_12BIT_1S_532US | INA219_CONFIG_MODE_SANDBVOLT_CONTINUOUS; wireWriteRegister(INA219_REG_CONFIG, config); } void Adafruit_INA219::setCalibration_16V_400mA(void) { // Calibration which uses the highest precision for // current measurement (0.1mA), at the expense of // only supporting 16V at 400mA max. // VBUS_MAX = 16V // VSHUNT_MAX = 0.04 (Assumes Gain 1, 40mV) // RSHUNT = 0.1 (Resistor value in ohms) // 1. Determine max possible current // MaxPossible_I = VSHUNT_MAX / RSHUNT // MaxPossible_I = 0.4A // 2. Determine max expected current // MaxExpected_I = 0.4A // 3. Calculate possible range of LSBs (Min = 15-bit, Max = 12-bit) // MinimumLSB = MaxExpected_I/32767 // MinimumLSB = 0.0000122 (12uA per bit) // MaximumLSB = MaxExpected_I/4096 // MaximumLSB = 0.0000977 (98uA per bit) // 4. Choose an LSB between the min and max values // (Preferrably a roundish number close to MinLSB) // CurrentLSB = 0.00005 (50uA per bit) // 5. Compute the calibration register // Cal = trunc (0.04096 / (Current_LSB * RSHUNT)) // Cal = 8192 (0x2000) ina219_calValue = 8192; // 6. Calculate the power LSB // PowerLSB = 20 * CurrentLSB // PowerLSB = 0.001 (1mW per bit) // 7. Compute the maximum current and shunt voltage values before overflow // // Max_Current = Current_LSB * 32767 // Max_Current = 1.63835A before overflow // // If Max_Current > Max_Possible_I then // Max_Current_Before_Overflow = MaxPossible_I // Else // Max_Current_Before_Overflow = Max_Current // End If // // Max_Current_Before_Overflow = MaxPossible_I // Max_Current_Before_Overflow = 0.4 // // Max_ShuntVoltage = Max_Current_Before_Overflow * RSHUNT // Max_ShuntVoltage = 0.04V // // If Max_ShuntVoltage >= VSHUNT_MAX // Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX // Else // Max_ShuntVoltage_Before_Overflow = Max_ShuntVoltage // End If // // Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX // Max_ShuntVoltage_Before_Overflow = 0.04V // 8. Compute the Maximum Power // MaximumPower = Max_Current_Before_Overflow * VBUS_MAX // MaximumPower = 0.4 * 16V // MaximumPower = 6.4W // Set multipliers to convert raw current/power values ina219_currentDivider_mA = 20; // Current LSB = 50uA per bit (1000/50 = 20) ina219_powerDivider_mW = 1; // Power LSB = 1mW per bit // Set Calibration register to 'Cal' calculated above wireWriteRegister(INA219_REG_CALIBRATION, ina219_calValue); // Set Config register to take into account the settings above uint16_t config = INA219_CONFIG_BVOLTAGERANGE_16V | INA219_CONFIG_GAIN_1_40MV | INA219_CONFIG_BADCRES_12BIT | INA219_CONFIG_SADCRES_12BIT_1S_532US | INA219_CONFIG_MODE_SANDBVOLT_CONTINUOUS; wireWriteRegister(INA219_REG_CONFIG, config); } /**************************************************************************/ /*! @brief Instantiates a new INA219 class */ /**************************************************************************/ Adafruit_INA219::Adafruit_INA219(uint8_t addr) { ina219_i2caddr = addr; ina219_currentDivider_mA = 0; ina219_powerDivider_mW = 0; } /**************************************************************************/ /*! @brief Setups the HW (defaults to 32V and 2A for calibration values) */ /**************************************************************************/ void Adafruit_INA219::begin(uint8_t addr) { ina219_i2caddr = addr | INA219_ADDRESS; ina219_currentDivider_mA = 0; ina219_powerDivider_mW = 0; begin(); } void Adafruit_INA219::begin(void) { Wire.begin(); // Set chip to large range config values to start setCalibration_32V_2A(); } /**************************************************************************/ /*! @brief Gets the raw bus voltage (16-bit signed integer, so +-32767) */ /**************************************************************************/ int16_t Adafruit_INA219::getBusVoltage_raw() { uint16_t value; wireReadRegister(INA219_REG_BUSVOLTAGE, &value); // Shift to the right 3 to drop CNVR and OVF and multiply by LSB return (int16_t)((value >> 3) * 4); } /**************************************************************************/ /*! @brief Gets the raw shunt voltage (16-bit signed integer, so +-32767) */ /**************************************************************************/ int16_t Adafruit_INA219::getShuntVoltage_raw() { uint16_t value; wireReadRegister(INA219_REG_SHUNTVOLTAGE, &value); return (int16_t)value; } /**************************************************************************/ /*! @brief Gets the raw current value (16-bit signed integer, so +-32767) */ /**************************************************************************/ int16_t Adafruit_INA219::getCurrent_raw() { uint16_t value; // Sometimes a sharp load will reset the INA219, which will // reset the cal register, meaning CURRENT and POWER will // not be available ... avoid this by always setting a cal // value even if it's an unfortunate extra step wireWriteRegister(INA219_REG_CALIBRATION, ina219_calValue); // Now we can safely read the CURRENT register! wireReadRegister(INA219_REG_CURRENT, &value); return (int16_t)value; } /**************************************************************************/ /*! @brief Gets the shunt voltage in mV (so +-327mV) */ /**************************************************************************/ float Adafruit_INA219::getShuntVoltage_mV() { int16_t value; value = getShuntVoltage_raw(); return value * 0.01; } /**************************************************************************/ /*! @brief Gets the shunt voltage in volts */ /**************************************************************************/ float Adafruit_INA219::getBusVoltage_V() { int16_t value = getBusVoltage_raw(); return value * 0.001; } /**************************************************************************/ /*! @brief Gets the current value in mA, taking into account the config settings and current LSB */ /**************************************************************************/ float Adafruit_INA219::getCurrent_mA() { float valueDec = getCurrent_raw(); valueDec /= ina219_currentDivider_mA; return valueDec; } /**************************************************/ /*** New functions we wrote as they were not ***/ /*** available with original Adafruit drivers. ***/ /**************************************************/ // Get Power from register #3. int16_t Adafruit_INA219::getPower_raw() { uint16_t value; // Write calibration value to calibration register, // otherwise power result will be unavailable. wireWriteRegister(INA219_REG_CALIBRATION, ina219_calValue); // Now we can safely read the CURRENT register! wireReadRegister(INA219_REG_POWER, &value); return (int16_t)value; } // Get Power in mW. float Adafruit_INA219::getPower_mW() { float valueDec = getPower_raw(); // Power Register content is multiplied by Power LSB which // is 20 times the Current_LSB for a power value in watts. valueDec *= ina219_powerDivider_mW; return valueDec; }