/*!
 *  @file Adafruit_BMP280.h
 *
 *  This is a library for the Adafruit BMP280 Breakout.
 *
 *  Designed specifically to work with the Adafruit BMP280 Breakout.
 *
 *  Pick one up today in the adafruit shop!
 *  ------> https://www.adafruit.com/product/2651
 *
 *  These sensors use I2C to communicate, 2 pins are required to interface.
 *
 *  Adafruit invests time and resources providing this open source code,
 *  please support Adafruit andopen-source hardware by purchasing products
 *  from Adafruit!
 *
 *  K.Townsend (Adafruit Industries)
 *
 *  BSD license, all text above must be included in any redistribution
 */
#ifndef __BMP280_H__
#define __BMP280_H__

#include "Adafruit_Sensor.h"
#include "Arduino.h"
#include <SPI.h>
#include <Wire.h>

/*!
 *  I2C ADDRESS/BITS/SETTINGS
 */
#define BMP280_ADDRESS (0x77) /**< The default I2C address for the sensor. */
#define BMP280_ADDRESS_ALT                                                     \
  (0x76)                     /**< Alternative I2C address for the sensor. */
#define BMP280_CHIPID (0x58) /**< Default chip ID. */

//  Forward declarations of Wire and SPI for board/variant combinations that
//  don't have a default 'Wire' or 'SPI'
extern TwoWire Wire; /**< Forward declaration of Wire object */
extern SPIClass SPI; /**< Forward declaration of SPI object */

/*!
 * Registers available on the sensor.
 */
enum {
  BMP280_REGISTER_DIG_T1 = 0x88,
  BMP280_REGISTER_DIG_T2 = 0x8A,
  BMP280_REGISTER_DIG_T3 = 0x8C,
  BMP280_REGISTER_DIG_P1 = 0x8E,
  BMP280_REGISTER_DIG_P2 = 0x90,
  BMP280_REGISTER_DIG_P3 = 0x92,
  BMP280_REGISTER_DIG_P4 = 0x94,
  BMP280_REGISTER_DIG_P5 = 0x96,
  BMP280_REGISTER_DIG_P6 = 0x98,
  BMP280_REGISTER_DIG_P7 = 0x9A,
  BMP280_REGISTER_DIG_P8 = 0x9C,
  BMP280_REGISTER_DIG_P9 = 0x9E,
  BMP280_REGISTER_CHIPID = 0xD0,
  BMP280_REGISTER_VERSION = 0xD1,
  BMP280_REGISTER_SOFTRESET = 0xE0,
  BMP280_REGISTER_CAL26 = 0xE1, /**< R calibration = 0xE1-0xF0 */
  BMP280_REGISTER_STATUS = 0xF3,
  BMP280_REGISTER_CONTROL = 0xF4,
  BMP280_REGISTER_CONFIG = 0xF5,
  BMP280_REGISTER_PRESSUREDATA = 0xF7,
  BMP280_REGISTER_TEMPDATA = 0xFA,
};

/*!
 *  Struct to hold calibration data.
 */
typedef struct {
  uint16_t dig_T1; /**< dig_T1 cal register. */
  int16_t dig_T2;  /**<  dig_T2 cal register. */
  int16_t dig_T3;  /**< dig_T3 cal register. */

  uint16_t dig_P1; /**< dig_P1 cal register. */
  int16_t dig_P2;  /**< dig_P2 cal register. */
  int16_t dig_P3;  /**< dig_P3 cal register. */
  int16_t dig_P4;  /**< dig_P4 cal register. */
  int16_t dig_P5;  /**< dig_P5 cal register. */
  int16_t dig_P6;  /**< dig_P6 cal register. */
  int16_t dig_P7;  /**< dig_P7 cal register. */
  int16_t dig_P8;  /**< dig_P8 cal register. */
  int16_t dig_P9;  /**< dig_P9 cal register. */
} bmp280_calib_data;

class Adafruit_BMP280;

/** Adafruit Unified Sensor interface for temperature component of BMP280 */
class Adafruit_BMP280_Temp : public Adafruit_Sensor {
public:
  /** @brief Create an Adafruit_Sensor compatible object for the temp sensor
      @param parent A pointer to the BMP280 class */
  Adafruit_BMP280_Temp(Adafruit_BMP280 *parent) { _theBMP280 = parent; }
  bool getEvent(sensors_event_t *);
  void getSensor(sensor_t *);

private:
  int _sensorID = 280;
  Adafruit_BMP280 *_theBMP280 = NULL;
};

/** Adafruit Unified Sensor interface for pressure component of BMP280 */
class Adafruit_BMP280_Pressure : public Adafruit_Sensor {
public:
  /** @brief Create an Adafruit_Sensor compatible object for the pressure sensor
      @param parent A pointer to the BMP280 class */
  Adafruit_BMP280_Pressure(Adafruit_BMP280 *parent) { _theBMP280 = parent; }
  bool getEvent(sensors_event_t *);
  void getSensor(sensor_t *);

private:
  int _sensorID = 0;
  Adafruit_BMP280 *_theBMP280 = NULL;
};

/**
 * Driver for the Adafruit BMP280 barometric pressure sensor.
 */
class Adafruit_BMP280 {
public:
  /** Oversampling rate for the sensor. */
  enum sensor_sampling {
    /** No over-sampling. */
    SAMPLING_NONE = 0x00,
    /** 1x over-sampling. */
    SAMPLING_X1 = 0x01,
    /** 2x over-sampling. */
    SAMPLING_X2 = 0x02,
    /** 4x over-sampling. */
    SAMPLING_X4 = 0x03,
    /** 8x over-sampling. */
    SAMPLING_X8 = 0x04,
    /** 16x over-sampling. */
    SAMPLING_X16 = 0x05
  };

  /** Operating mode for the sensor. */
  enum sensor_mode {
    /** Sleep mode. */
    MODE_SLEEP = 0x00,
    /** Forced mode. */
    MODE_FORCED = 0x01,
    /** Normal mode. */
    MODE_NORMAL = 0x03,
    /** Software reset. */
    MODE_SOFT_RESET_CODE = 0xB6
  };

  /** Filtering level for sensor data. */
  enum sensor_filter {
    /** No filtering. */
    FILTER_OFF = 0x00,
    /** 2x filtering. */
    FILTER_X2 = 0x01,
    /** 4x filtering. */
    FILTER_X4 = 0x02,
    /** 8x filtering. */
    FILTER_X8 = 0x03,
    /** 16x filtering. */
    FILTER_X16 = 0x04
  };

  /** Standby duration in ms */
  enum standby_duration {
    /** 1 ms standby. */
    STANDBY_MS_1 = 0x00,
    /** 62.5 ms standby. */
    STANDBY_MS_63 = 0x01,
    /** 125 ms standby. */
    STANDBY_MS_125 = 0x02,
    /** 250 ms standby. */
    STANDBY_MS_250 = 0x03,
    /** 500 ms standby. */
    STANDBY_MS_500 = 0x04,
    /** 1000 ms standby. */
    STANDBY_MS_1000 = 0x05,
    /** 2000 ms standby. */
    STANDBY_MS_2000 = 0x06,
    /** 4000 ms standby. */
    STANDBY_MS_4000 = 0x07
  };

  Adafruit_BMP280(TwoWire *theWire = &Wire);
  Adafruit_BMP280(int8_t cspin, SPIClass *theSPI = &SPI);
  Adafruit_BMP280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
  ~Adafruit_BMP280(void);

  bool begin(uint8_t addr = BMP280_ADDRESS, uint8_t chipid = BMP280_CHIPID);
  void reset(void);
  uint8_t getStatus(void);
  uint8_t sensorID(void);

  float readTemperature();
  float readPressure(void);
  float readAltitude(float seaLevelhPa = 1013.25);
  float seaLevelForAltitude(float altitude, float atmospheric);
  float waterBoilingPoint(float pressure);

  Adafruit_Sensor *getTemperatureSensor(void);
  Adafruit_Sensor *getPressureSensor(void);

  // void takeForcedMeasurement();
  void setSampling(sensor_mode mode = MODE_NORMAL,
                   sensor_sampling tempSampling = SAMPLING_X16,
                   sensor_sampling pressSampling = SAMPLING_X16,
                   sensor_filter filter = FILTER_OFF,
                   standby_duration duration = STANDBY_MS_1);

private:
  TwoWire *_wire; /**< Wire object */
  SPIClass *_spi; /**< SPI object */

  Adafruit_BMP280_Temp *temp_sensor = NULL;
  Adafruit_BMP280_Pressure *pressure_sensor = NULL;

  /** Encapsulates the config register */
  struct config {
    /** Inactive duration (standby time) in normal mode */
    unsigned int t_sb : 3;
    /** Filter settings */
    unsigned int filter : 3;
    /** Unused - don't set */
    unsigned int none : 1;
    /** Enables 3-wire SPI */
    unsigned int spi3w_en : 1;
    /** Used to retrieve the assembled config register's byte value. */
    unsigned int get() { return (t_sb << 5) | (filter << 2) | spi3w_en; }
  };

  /** Encapsulates trhe ctrl_meas register */
  struct ctrl_meas {
    /** Temperature oversampling. */
    unsigned int osrs_t : 3;
    /** Pressure oversampling. */
    unsigned int osrs_p : 3;
    /** Device mode */
    unsigned int mode : 2;
    /** Used to retrieve the assembled ctrl_meas register's byte value. */
    unsigned int get() { return (osrs_t << 5) | (osrs_p << 2) | mode; }
  };

  void readCoefficients(void);
  uint8_t spixfer(uint8_t x);
  void write8(byte reg, byte value);
  uint8_t read8(byte reg);
  uint16_t read16(byte reg);
  uint32_t read24(byte reg);
  int16_t readS16(byte reg);
  uint16_t read16_LE(byte reg);
  int16_t readS16_LE(byte reg);

  uint8_t _i2caddr;

  int32_t _sensorID;
  int32_t t_fine;
  int8_t _cs, _mosi, _miso, _sck;
  bmp280_calib_data _bmp280_calib;
  config _configReg;
  ctrl_meas _measReg;
};

#endif